The thermal efficiency of a reversible heat engine operating between two given thermal reservoirs is 0.4. The device is used either as a refrigerator or as a heat pump between the same reservoirs. Then the coefficient of performance as a refrigerator (COP)R and the co-efficient of performance as a heat pump (COP)HP are _______________?

Related Mcqs:

1. Fouling factor for a heat exchanger is given by (where, U1 = heat transfer co-efficient of dirty surface U2 = heat transfer co-efficient of clean surface) ?

   A. U1 – U2
   B. 1/U1 – 1/U2
   C. 1/U2 – 1/U1
   D. U2 – U1

2. The overall heat transfer co-efficient for a shell and tube heat exchanger for clean surfaces is U0 = 400 W/m2.K. The fouling factor after one year of operation is found to be hd0 = 2000 W/m2.K. The overall heat transfer co-efficient at this time is _____________________?

   A. 1200 W/m2.K
   B. 894 W/m2.K
   C. 333 W/m2.K
   D. 287 W/m2.K

3. Overall heat transfer co-efficient of a particular tube is U1. If the same tube with some dirt deposited on either side has coefficient U2, then_________________?

   A. U1 = U2
   B. U2 > U1
   C. U1 > U2
   D. U1 = dirt factor – U2

4. The inner wall of a furnace is at a temperature of 700°C. The composite wall is made of two substances, 10 and 20 cm thick with thermal conductivities of 0.05 and 0.1 W.m-1.°C- 1 respectively. The ambient air is at 30°C and the heat transfer co-efficient between the outer surface of wall and air is 20 W.m-2.°C-1. The rate of heat loss from the outer surface in W.m-2is__________________?

   A. 165.4
   B. 167.5
   C. 172.5
   D. 175

5. A 10 cm dia steam pipe, carrying steam at 180°C, is covered with an insulation (conductivity = 0.6 W/m.°C). It losses heat to the surroundings at 30°C. Assume a heat transfer co-efficient of 0.8 W/m2.°C for heat transfer from surface to the surroundings. Neglect wall resistance of the pipe and film resistance of steam. If the insulation thickness is 2 cms, the rate of heat loss from this insulated pipe will be__________________?

   A. Greater than that for un-insulated steam pipe
   B. Less than that of the un-insulated steam pipe
   C. Equal to that of the un-insulated steam pipe
   D. Less than the steam pipe with 5 cms insulation

6. Extended heat transfer surface like fins are used to increase the heat transfer rate. Fin efficiency is defined as the ratio of heat transferred across the fin surface to the theoretical heat transfer across an equal area held at the________________?

   A. Surrounding temperature
   B. Average temperature of the fin
   C. Temperature of the fin end
   D. Constant temperature equal to that of the base

7. If h1 = inner film co-efficient and /h2 = outer film co-efficient, then the overall heat transfer co-efficient is________________?

   A. Always less than h1
   B. Always between h1 and h2
   C. Always higher than h2
   D. Dependent on metal resistance

8. If average heat transfer co-efficient is ha and the local coefficient at the end of the plate is hl then in case of heat transfer to a fluid flowing over a flat plate, heated over its entire length________________?

   A. ha = hl
   B. ha = 2hl
   C. ha = 0.5 hl
   D. ha = 0.75 hl

9. For a laminar flow of fluid in a circular tube, ‘h1’ is the convective heat transfer co-efficient at velocity ‘V1’. If the velocity is reduced by half and assuming the fluid properties are constant, the new convective heat transfer co-efficient is________________?

   A. 1.26 h1
   B. 0.794 h1
   C. 0.574 h1
   D. 1.741 h1

10. For turbulent flow in a tube, the heat transfer co-efficient is obtained from the Dittus- Boelter correlation. If the tube diameter is halved and the flow rate is doubled, then the heat transfer co-efficient will change by a factor of________________?

    A. 1
    B. 1.74
    C. 6.1
    D. 37