A. 2/3 kW
B. 1 kW
C. 5/3 kW
D. 4 kW
Related Mcqs:
- An irreversible aqueous phase reaction, A + B → P, is carried out in an adiabatic mixed flow reactor. A feed containing 4kmole/m3 of each A and B enters the reactor at 8m3 /hr. If the temperature of the exit stream is never to exceed 390 K, what is the maximum inlet feed temperature allowed? Data: Heat of reaction = – 50 kJ/mole Density of the reacting mixture = 1000kg/m3 Specific heat of reacting mixture = 2kJ/kg.K The above data can be assumed to be independent of temperature and composition?
A. 190
B. 290
C. 390
D. 490 - In a chemical reaction, represented by as shown in the bellow figure, it is observed that the (i) Rate of reaction increases by a factor of 4 on doubling the concentration of the reactant. (ii) Rate of reaction increases by a factor of 9 on trebling the concentration of the reactant. Then the rate of the reaction is proportional to(where, CA = concentration of the reactant)_____________________?
A. CA
B. CA2
C. CA3
D. CA4 - A batch adiabatic reactor at an initial temperature of 373°K is being used for the reaction, A → B. Assume the heat of reaction is – 1kJ/mole at 373°K and heat capacity of both A and B to be constant and equal to 50J/mole.K. The temperature rise after a conversion of 0.5 will be ____________?
A. 5°C
B. 10°C
C. 20°C
D. 100°C - For the liquid phase zero order irreversible reaction A → B, the conversion of A in a CSTR is found to be 0.3 at a space velocity of 0.1min-1. What will be the conversion for a PFR with a space velocity of 0.2 min-1? Assume that all the other operating conditions are the same for CSTR and PFR ?
A. 0.15
B. 0.30
C. 0.60
D. 0.90 - The reaction A → B is conducted in an adiabatic plug flow reactor (PFR). Pure A at a concentration of 2 kmol/m3is fed to the reactor at the rate of 0.01 m3 /s and at a temperature of 500 K. If the exit conversion is 20%, then the exit temperature (in k) is (Data: Heat of reaction at 298 K = – 50000 kJ/ kmole of A reacted Heat capacities CPA = CPB = 100kJ/kmole. K (may be assumed to be independent of temperature)) ?
A. 400
B. 500
C. 600
D. 1000 - The gas phase reaction 2A ⇌ B is carried out in an isothermal plug flow reactor. The feed consists of 80 mole % A and 20 mole % inerts. If the conversion of A at the reactor exit is 50%, then CA/CA0 at the outlet of the reactor is _______________________?
A. 2/3
B. 5/8
C. 1/3
D. 3/8 - A second order liquid phase reaction, A → B, is carried out in a mixed flow reactor operated in semi batch mode (no exit stream). The reactant A at concentration CAF is fed to the reactor at a volumetric flow rate of F. The volume of the reacting mixture is V and the density of the liquid mixture is constant. The mass balance for A is_______________________?
A. d(VCA)/dt = -F (CAF – CA) – kCA2V
B. d(VCA)/dt = F (CAF – CA) – kCA2V
C. d(VCA)/dt = -FCA – kCA2V
D. d(VCA)/dt = FCAF – kCA2V - The conversion for a first order liquid phase reaction. A → B in a CSTR is 50%. If another CSTR of the same volume is connected in series, then the % conversion at the exit of the second reactor will be_____________________?
A. 60
B. 75
C. 90
D. 100 - Rate constant for a first order reaction does not depend upon reaction time, extent of reaction and the initial concentration of reactants; but it is a function of reaction temperature. In a chemical reaction, the time required to reduce the concentration of reactant from 100 gm moles/litre to 50 gm moles/litre is same as that required to reduce it from 2 gm moles/litre to 1 gm mole/litre in the same volume. Then the order of this reaction is ?
A. 0
B. 1
C. 2
D. 3 - Pure ethanol vapor is fed to a reactor packed with alumina catalyst, at the rate of 100 kmole / hr. The reactor products comprise: ethylene: 95 kmole / hr, water vapour: 97.5 k mole / hr and diethyl ether: 2.5 kmole/hr. The reactions occuring can be represented by: C2H5OH → C2H4 + H2O 2C2H5OH → C2H5 – O – C2H5 + H2O The percent conversion of ethanol in the reactor is________________?
A. 100
B. 97.5
C. 95
D. 2.5
