A. alien nut
B. hexagonal nut
C. slotted nut
D. castle nut
E. any one of the above
Related Mcqs:
- The pitch of threads on a Jock nut in comparison to pitch of nut is_________________?
A. same
B. coarser
C. finer
D. very coarse
E. very fine - For standard coarse threads of nut, the threads will be as strong in failure by shear as the bolt in tension, if the height of nut (h) is approximately________________?
A. 0.4 times
B. 0.6 times
C. 0.7 times
D. 0.8 times
E. 0.9 times the normal diameter of bolt - If shearing stress in nut is half the tensile stress in a bolt, then nut length should be equal to___________________?
A. diameter of bolt
B. 0.75 x diameter of bolt
C. 1.25 x diameter of bolt
D. 1.5 x diameter of bolt
E. 0.5 x diameter of bolt - When a nut is tightened by plaping a washer below it, the bolt will be subjected to following type of loads___________________?
A. compression
B. tension
C. shear
D. combined loads
E. all of the above - An alien bolt is___________________?
A. self locking bolt
B. same as stud
C. provided with hexagonal depression in head
D. used in high speed components
E. provided with countersunk head - Castle nut is a locking device in which__________________?
A. one smaller nut is tightened over main nut and main nut tightened against smaller one by loosening, creating friction jamming
B. a slot is cut partly is middle of nut and then slot reduced by tightening a screw
C. a hard fiber or nylon cotter is recessed in the nut and becomes threaded as the nut is screwed on the bolt causing a tight grip
D. through slots are made at top and a cotter pin is passed through these and a hole in the bolt, and cotter pin spitted and bent in reverse direction at other end
E. none of the above. - Split nut is a locking device in which_________________?
A. one smaller nut is tightened over main nut and main nut tightened against smaller one by loosening, creating friction jamming
B. a slot is cut partly in middle of nut and then slot reduced by tightening screw
C. a hard fiber or nylon cotter is recessed in the nut and becomes threaded as the nut is screwed on the bolt causing a tight grip
D. through slots are made at top and a cotter-pin is passed through these and a hole in the bolt, and cotter pin splitted and bent in reverse direction at the other end
E. none of the above - If threads on a bolt are left hand, threads on nut will be_____________________?
A. right hand with same pitch
B. left hand with same pitch
C. could be left or right hand
D. right hand with fine pitch
E. left hand with fine pitch - Elastic nut is a locking device in which__________________?
A. one small nut is tightened over main nut and main nut tightened against smaller one by loosening, creating friction jamming
B. a slot is cut partly in middle of nut and then slot reduced by tightening a screw
C. hard fiber or nylon cotter is recessed in the nut and becomes threaded as the nut is stewed on the bolt causing a tight grip
D. through slots are made at top and a cotter-pin is passed through these and a hole in the bolt, and cotter pin splitted and bent in reverse direction at other end
E. none of the above - Jam nut is a locking device in which _____________________?
A. one smaller nut is tightened over main nut and main nut tightened against smaller one by loosening, creating friction jamming
B. a slot is cut partly in middle of nut and then slot reduced by tightening a screw
C. a hard fiber or nylon cotter is recessed in the nut and becomes threaded as the nut is screwed on the bolt causing a tight grip
D. through slots are made at top and a cotter-pin is passed through these and a hole in the bolt, and cotter spitted and bent in reverse direction at other end
E. none of the above
