A. individual component parameters
B. a percent of the total power depending on resistor ratios
C. total current squared multiplied by the resistor values
D. a percent of the voltage division ratio squared
Related Mcqs:
- In a series–parallel circuit consisting of R1 and R2 in series and connected in parallel with R3, if R1 opens, then R2‘s voltage will:___________?
A. increase
B. remain the same
C. decrease
D. cannot tell - The parallel combination of a 470 Ω resistor and a 1.2 kΩ resistor is in series with the parallel combination of three 3 kΩ resistors. A 200 V source is connected across the circuit. The resistor with the most current has a value of____________?
A. 470 Ω or 1.2 kΩ
B. 3 kΩ
C. 470 Ω
D. 1.2 kΩ - The parallel combination of a 6.8 kΩ resistor and a 10 kΩ resistor is in series with the parallel combination of a 2.2 kΩ resistor and a 1 kΩ resistor. A 100 V source is connected across the circuit. The resistor(s) with the greatest voltage drop is (are)___________?
A. 6.8 kΩ
B. 2.2 kΩ
C. 6.8 kΩ and 10 kΩ
D. 2.2 kΩ and 1 kΩ - What will be the collector efficiency of a power amplifier having zero signal power dissipation of 5 watts and a.c. power output of 2 watts ?
A. 20%
B. 80%
C. 40%
D. 50% - The parallel combination of a 470 Ω resistor and a 1.5 kΩ resistor is in series with the parallel combination of five 1 kΩ resistors. The source voltage is 50 V. The percentage of the load current through any single 1 KΩ resistor is__________?
A. 25 %
B. 20 %
C. 100 %
D. 50 % - The parallel combination of a 470 Ω resistor and a 680 Ω resistor is in series with the parallel combination of four 2 kΩ resistors. The total resistance is___________?
A. 1,650 Ω
B. 1,078 Ω
C. 77.8 Ω
D. 778 Ω - Three 10 kΩ resistors are connected in series. A 20 kΩ resistor is connected in parallel across one of the 10 kΩ resistors. The voltage source is 24 V. The total current in the circuit is___________?
A. 900 μA
B. 9 mA
C. 90 mA
D. 800 μA - With 21 V applied, if R1 = 5 ohms, R2 = 35 ohms, and R3 = 14 ohms, what is the current of R2 if R1 is series connected with parallel circuit R2 and R3?
A. 200 mA
B. 400 mA
C. 600 mA
D. 800 mA - The first goal to accomplish in analyzing a complex series-parallel circuit is to____________?
A. solve for all the voltage drops
B. solve for the total current and resistance
C. equate all series components
D. equate all parallel components - A parallel resonant band-pass filter consists of a 90 Ω resistor in series with a parallel network made up of a 60 mH coil and a 0.02 µF capacitor. The output is taken across the capacitor/coil. The coil winding has a resistance of 20 Ω. What is the center frequency of the filter?
A. 459 Hz
B. 4,591 Hz
C. 999 Hz
D. 2,176 Hz
Advertisement
