A. Spray dryer
B. Spouted bed dryer
C. Tunnel dryer
D. Pan open to atmosphere
Related Mcqs:
- A 25 cm × 25 cm × 1 cm flat sheet weighing 1.2 kg initially was dried from both sides under constant drying rate conditions. It took 1500 seconds for the weight of the sheet to reduce to 1.05 kg. Another 1m × 1m × 1cm flat sheet of the same material is to be dried from one side only. Under the same constant drying rate conditions, the time required for drying (in seconds) from its initial weight of 19.2 kg to 17.6 kg is ____________________?
A. 1000
B. 1500
C. 2000
D. 2500 - Compound A is extracted from a solution of A + B into a pure solvent S. A Co-current unit is used for the liquid-liquid extraction. The inlet rate of the solution containing A is 200 moles of B/hr.m2 and the solvent flow, rate is 400 moles of S/m2. hr. The equilibrium data is represented by Y = 3X2 , where Y is in moles of a A/moles of B and X is in moles A/moles of S. The maximum percentage extraction achieved in the unit is_________________________?
A. 25%
B. 50%
C. 70%
D. 90% - If the solubilities of different components (in a liquid-liquid extraction system) increase with rise in temperature, then the temperature above which they dissolve completely is known as the critical solution temperature (CST or consolute temperature). If solubilities increase with decrease in temperature, then CST is the temperature below which they dissolve completely. If a binary system has no critical solution temperature, it implies that___________________?
A. The system comprises of partially miscible liquids
B. The system comprises of miscible liquids
C. The system comprises of an azeotrope
D. On heating, a vapor phase will appear; while on cooling, a solid phase will appear - Dried finished product sampled from various parts of a ________________ dryer exhibits nonuniformity in the moisture content?
A. Rotary
B. Tray
C. Freeze
D. None of these - A solid is being dried in the linear drying rate regime from moisture content Xo to XF. The drying rate is zero at X = 0 and the critical moisture content is the same as the initial moisture Xo. The drying time for M = (Ls/ARc) is (where, L = total mass of dry solid, A = total surface area for drying Rc = Constant maximum drying rate per unit area X = moisture content (in mass of water/mass of dry solids)) ?
A. M(Xo – XF)
B. M(Xo/XF)
C. M ln(Xo/XF)
D. MXo ln(Xo/XF) - A solid is being dried in the linear drying rate regime from moisture content Xo to XF. The drying rate is zero at X = 0 and the critical moisture content is the same as the initial moisture Xo. The drying time for M = (Ls/ARc) is (where, L = total mass of dry solid, A = total surface area for drying Rc = Constant maximum drying rate per unit area X = moisture content (in mass of water/mass of dry solids))_____________?
A. M(Xo – XF)
B. M(Xo/XF)
C. M ln(Xo/XF)
D. MXo ln(Xo/XF) - Free flowing granular materials can be best dried in a __________________ drier?
A. Rotary
B. Cylinder
C. Drum
D. Freeze - Milk is dried usually in a __________________ dryer?
A. Freeze
B. Spray
C. Tray
D. Rotary - Sand is dried in foundries in a ______________________drier?
A. Rotary
B. Fluidised bed
C. Vacuum
D. Spray - Sticky material can be dried in a ________________ dryer ?
A. Tray
B. Rotary
C. Fluidised bed
D. None of these
