Maximum heat transfer rate is achieved in _____________ flow?

Related Mcqs:

1. Extended heat transfer surface like fins are used to increase the heat transfer rate. Fin efficiency is defined as the ratio of heat transferred across the fin surface to the theoretical heat transfer across an equal area held at the________________?

   A. Surrounding temperature
   B. Average temperature of the fin
   C. Temperature of the fin end
   D. Constant temperature equal to that of the base

2. A 10 cm dia steam pipe, carrying steam at 180°C, is covered with an insulation (conductivity = 0.6 W/m.°C). It losses heat to the surroundings at 30°C. Assume a heat transfer co-efficient of 0.8 W/m2.°C for heat transfer from surface to the surroundings. Neglect wall resistance of the pipe and film resistance of steam. If the insulation thickness is 2 cms, the rate of heat loss from this insulated pipe will be__________________?

   A. Greater than that for un-insulated steam pipe
   B. Less than that of the un-insulated steam pipe
   C. Equal to that of the un-insulated steam pipe
   D. Less than the steam pipe with 5 cms insulation

3. For turbulent flow in a tube, the heat transfer co-efficient is obtained from the Dittus- Boelter correlation. If the tube diameter is halved and the flow rate is doubled, then the heat transfer co-efficient will change by a factor of________________?

   A. 1
   B. 1.74
   C. 6.1
   D. 37

4. The Sieder-Tate correlation for heat transfer in turbulent flow in pipe gives Nu α Re0.8, where, Nu is the Nusselt number and Re is the Reynolds number for the flow. Assuming that this relation is valid, the heat transfer co-efficient varies with the pipe diameter D. as _________________?

   A. D-1.8
   B. D-0.2
   C. D0.2
   D. D1.8

5. A fluid is flowing inside the inner tube of a double pipe heat exchanger with diameter ‘d’. For a fixed mass flow rate, the tube side heat transfer co-efficient for turbulent flow conditions is proportional to_____________________?

   A. d0.8
   B. d-0.2
   C. d-1
   D. d-1.8

6. Heat transfer by conduction results due to the transfer of free electrons, kinetic energy & vibrational energy from one molecule to another. Conduction heat transfer cannot take place____________________?

   A. Between two bodies in physical contact with each other
   B. Between two bodies not in physical contact with each other
   C. From one part of a body to the another part of the same body
   D. Both B & C

7. Fouling factor for a heat exchanger is given by (where, U1 = heat transfer co-efficient of dirty surface U2 = heat transfer co-efficient of clean surface) ?

   A. U1 – U2
   B. 1/U1 – 1/U2
   C. 1/U2 – 1/U1
   D. U2 – U1

8. The overall heat transfer co-efficient for a shell and tube heat exchanger for clean surfaces is U0 = 400 W/m2.K. The fouling factor after one year of operation is found to be hd0 = 2000 W/m2.K. The overall heat transfer co-efficient at this time is _____________________?

   A. 1200 W/m2.K
   B. 894 W/m2.K
   C. 333 W/m2.K
   D. 287 W/m2.K

9. For shell and tube heat exchanger, with increasing heat transfer area, the purchased cost per unit heat transfer area___________________?

   A. Increases
   B. Decreases
   C. Remain constant
   D. Passes through a maxima

10. For a laminar flow of fluid in a circular tube, ‘h1’ is the convective heat transfer co-efficient at velocity ‘V1’. If the velocity is reduced by half and assuming the fluid properties are constant, the new convective heat transfer co-efficient is________________?

    A. 1.26 h1
    B. 0.794 h1
    C. 0.574 h1
    D. 1.741 h1